Installing a Live Edge Spalted Sycamore Bartop
Last week we delivered and installed a bartop after a nice long drive to the customer’s house, which made for some nice quality time in the truck with Tom.
The live-edge sycamore top was nicely spalted, so it had some extra character. Spalting happens in all wood (some more than others) when it starts to decay. The trick is to mill the logs at the right time, so they have more visual interest but haven’t rotted too much. For sycamore, the right amount of time for the log to sit for optimal spalting is around the one-year range. However, the wood can be spalted and still useable for up to three years. This timing is widely variable depending on climate and storage conditions, and you can’t really know the results until the log is milled.
The customer plans to install decorative brackets later, but we still installed steel plates, which add support and give us a place to fasten down the top. Before finishing with Krystal conversion varnish, Tom milled slots in the bottom of the slab with the CNC router to accept the steel plates, which tuck in underneath. To see how it all came together, check out the video below.
Milling a 5-year-old cypress log
We have a kitchen remodel which we are working on in the shop and the wood of choice is cypress to match a door I built about 15-years ago. To match the rustic setting of his cabin, the customer recently decided to cover a wall with cypress and we needed a little more lumber. I had a few remaining cypress logs that have been there for about five years, so I took a gamble and milled them to see what I could get. It was a small gamble because cypress is very rot resistant, and it is common for us to find logs in this condition and still find plenty of good wood inside (click here to read more about milling rotten logs). The sapwood was starting to rot, which happens first in all species, no matter how rot resistant they are, but most of the heartwood was fine.
Check out the video below to see the process and hang out with me on a nice winter day at the sawmill.
Asian-inspired mahogany shelves fit right in
We recently installed a set of three mahogany shelves with an asian inspiration. Our customer, who also happens to have a parent from Thailand, lived in Japan while she was in the military where she was inspired by the architecture. There is an air of this asian influence in the house already and she wanted to continue with that theme in her hallway along the stairs. She sketched up the design for the three units and let us roll from there.
The units are built out of solid wood, 8/4 mahogany, with most of the boards single width. They are connected with Domino connectors from Festool, which is a new favorite for loose tenon wood joinery. They are fast, accurate and strong, and quickly becoming the new standard in the industry, even if everyone doesn’t want to admit it (more on that some other day).
Most of the video below is focused on the finishing process, which is also where most of the time was spent. It included plenty of sanding before construction and tons more after. The mahogany is rather soft, so any rough handling along the way just added to all of the sanding fun.
I used Minwax Espresso stain for the color and Magnalac (modified lacquer) for the finish. I like the ease of application of the Magnalac and its forgiveness if I need to rework any areas.
The shelves fit into existing openings, and even though I didn’t show it in the video, they did actually get some fasteners after the satisfying slide into place (it just seemed like a great place to end the video).
Badass live edge walnut conference room table
We just delivered a walnut conference room table and I have been doing my best to describe it. I feel like it’s a bit aggressive and perhaps a little braggy, but after I show the photos, I get agreement on the word “badass”.
It started with a sketch from the customer (a pretty good one, by the way) of what he envisioned. I didn’t know at the time how it would go together, but I don’t worry about pesky details, so I just got to work.
Up first was how to fasten the top to the base and second, whether or not the base would need to break down for transport. Although it isn’t necessary for it to breakdown, I thought it would be cool if it could. After Jeff, our resident builder and CNC guy had the idea to use bed rail hardware, I realized the base could go together and break down without tools or visible hardware, and I knew I had to do the same for the top.
I messed with lots of different ways to attach the live edge top(s) and finally ended up with a sliding spline joint that allowed it to completely assemble without tools. As I worked on it, I got more drawn into and obsessed with the assembly part and didn’t really get a chance to appreciate how pretty it was until the final assembly at the customer’s office. Even if the design isn’t for you, I think you’ll agree – it’s badass.
Click on the link below to watch the video of the table build from picking out the wood through the delivery.
Big live edge slabs
We’ve been working with more and more big live edge slabs, and this week was no exception. We sold and need to dry one of the largest oak slabs we have cut, so it’s getting a little extra time in the kiln. After we got done loading the slab, Kyle showed up with some big pecan slabs that he milled for us. The log is a giant from the Mississippi River flood plain which he busted in half to handle.
Kyle built his own band sawmill a few years ago which will cut 6′ wide, and he has been cutting for us ever since. Kyle is basically a WunderWoods employee, at least as far as I am concerned, but I haven’t been able to convince him to do it officially. Everybody loves Kyle and we have a good time when he shows up. I don’t even mind if everybody stops working when he arrives.
Below is a video of us working with the big red oak slab and Kyle’s delivery.
What’s Going on at WunderWoods
Everyone always asks what I do. Here's the answer. Click on the photo above for a short video tour and see all of the steps it takes to go from a tree to finished furniture.